Specific Heat Capacity Paper

Published: 2021-09-11 21:10:09
essay essay

Category: Chemistry

Type of paper: Essay

This essay has been submitted by a student. This is not an example of the work written by our professional essay writers.

Hey! We can write a custom essay for you.

All possible types of assignments. Written by academics

In this experiment, we are going to use a calorimeter (a solid metal block of aluminium). And we are going to expose it to different temperatures and measure the difference in temperature over time. We will also measure the changes in electric properties from the heater over time: Volts and Amperes. In order to get more precise data, we are going to repeat this experiment twice with different power and the second trial will use stronger voltage. The reason that we are going to perform two trials is to try to minimize the error due to heat lost.
The value that we get is 528 J Kg-1K-1. Theoretically, the Specific Heat Capacity of Aluminium is 897J g-1 ½K-1. I presume that we may have lost some of the heat to the air as well as to metal expansion. In order to minimize the error due to heat, we repeated the same experiment with different levels of power. This allows us to minimize the uncertainties due to heat loss by isolating them from the original equation. Even though we were tried to lower the value of error, it was difficult to minimize it without completely insulating the calorimeter.
There are some doubts about the fact that the heater is sometimes warming the calorimeter quickly, whilst it sometimes takes a longer period. I am not sure about the reason for this phenomenon. Sensible variations were detected during the experiment. A suggestion would be to use a more accurate heater or digital thermometer for further testing. In order to get more precise data, we should definitely insulate the calorimeter to minimize its heat lost to the surroundings. For instance, we may place bubble wrap, foil or Styrofoam around the calorimeter. To obtain more accurate results in the future, a good idea may be to perform the experiment more than twice. Even if the heat loss variable is set aside after more than one experiment, we might get more reliable data by overcoming the variations we have observed in heat transmission between the heater and calorimeter.
The specific heat capacity of the objects can be calculated because the heat gained in the reaction is equal to the heat lost during the reaction. Due to the concept of thermal equilibrium we know that when objects of differing temperatures are in contact with each other, in this case the block, the water and Aluminum calorimeter they will eventually transfer heat to the point at which they are the same temperature. By measuring the temperature before the blocks were added to the water and then again when the temperature remains constant indicating equilibrium temperature the change in temperature was able to be calculated and using this along with the mass of the objects and water and calorimeter the specific heat capacity could be calculated using the Q=mc?T formula.
For the “How cold is it in the freezer compartment?” question an aluminum block was placed in the freezer and then placed into the water in the calorimeter of which the temperature had been recorded. The temperature of the water with the Aluminum block was recorded until the constant temperature was reached. With this we can calculate the initial temperature of the aluminum block which gives us the temperature of the freezer.
There were several limitations in the equipment used to carry out the procedure. The scale used to measure the mass of the aluminum calorimeter and water only measured up to 200g this was a major limitation as it only allowed for a small amount of water to be added to the calorimeter which may have affected the heat transfer as the submerged block may not have been fully submerged therefore some heat may have been lost to the air.
In moving the heated block from the boiling water to the calorimeter the block could have lost heat but this would be minimal due to the relatively high Specific heat capacities of the blocks. When the block was moved into the calorimeter it was dropped into it and this caused some water to splash out which would decrease the mass of water in the calorimeter which could affect the overall temperature change. The value for the specific heat capacity (shc) of object one which was Iron was compared to the theoretical value for the shc of Iron and gave a 17.6% difference this value is relatively high and could be due to uncertainties in the measurements and errors produced from the procedure.
The % difference of object two was very large at 31.3% this could be due to random error but more likely due to the block not being fully submerged as I mentioned earlier. The value of the percentage difference for Object3 which was Copper was relatively high at 17.2%, In order to improve upon the experiment a scale that measures up to a higher mass such as 500g. Another method to improve the experiment would be to add more water to the calorimeter in order to insure the block was fully submerged. Another improvement that could be made would be to not drop the blocks into the calorimeter and therefore minimize the risk of losing water after the mass was taken.

Warning! This essay is not original. Get 100% unique essay within 45 seconds!


We can write your paper just for 11.99$

i want to copy...

This essay has been submitted by a student and contain not unique content

People also read